Dispatch in 3–7 working days · 1-year warranty on every part Call A Rep: +86 13537510010 | Request A Quote
Inspected & Load-Tested Before Dispatch Serial Recorded Dispatch in 3–7 working days
MZ7L31T9HBNA · Samsung

Samsung PM897 1.92TB SATA SSD (MZ7L31T9HBNA)

1.92 TB 2.5-inch SATA mixed-use SSD, ordering code MZ7L31T9HBNA-00B7C

New Used
Pricing Request quote
MOQ 2 pc · volume pricing on request
Reply Within 24h
Volume Pricing
Worldwide Shipping
Secure Anti-Static Pack
Part Number
MZ7L31T9HBNA
Brand
Samsung
Category
Enterprise & Data Center SSD
Accepted Payments
T/T Bank Transfer PayPal Western Union

Technical Specifications

Capacity 1.92 TB
Interface SATA
Form Factor 2.5-inch 7mm
PCIe Version Not applicable
NAND Type TLC
Endurance (DWPD) 3
TBW 10,512 TB
Sequential Read 560 MB/s
Sequential Write 530 MB/s
Random Read IOPS 97K IOPS
Random Write IOPS 60K IOPS
Power 2.3 W
DRAM Cache Yes
Power Loss Protection Yes
Encryption Opal 2.0
Condition New · Used

Frequently Asked Questions

The catalogue code is MZ7L31T9HBNA and the ordering code is MZ7L31T9HBNA-00B7C. The build code changes at this capacity: the 480 GB and 960 GB members carry HBLT, while this drive and the 3.84 TB member carry HBNA. Both are the same 7 mm 2.5-inch SATA drive with the same -00B7C ordering suffix, so the label is what distinguishes them.

No. Samsung publishes one performance table for the whole PM897 range, so every capacity runs 560/530 MB/s, 97K/60K IOPS, 95/90 consistency and 2.3/3.0 W. Only the TBW column is split: 2,628 TB at 480 GB, 5,256 TB at 960 GB, 10,512 TB here. The step up buys bytes, write budget and roles, not speed.

No, and it is worth knowing that before comparing on endurance alone. The SM863a at 1.92 TB carries 3.5 DWPD and 12,320 TBW on 2-bit MLC, about 17% more write budget than this drive. What it gives up is throughput: 510/485 MB/s against 560/530, and 28K random write against 60K. If the workload queues writes, this drive completes more than twice the write operations per second.

About an hour at 530 MB/s for a full 1.92 TB rewrite, and for that hour a mirrored pair is unprotected and a parity set runs on reduced redundancy. That is the number to weigh when consolidating four 480 GB drives into one of these: four devices become one, along with three ports and three idle draws, and a single failure costs an hour of exposure instead of the fifteen minutes a 480 GB rebuild takes.

Both, and both are documented. Capacitor hold-up transfers cached DRAM data to flash when a failure is detected, so in-flight writes survive a short interruption, though Samsung publishes no hold-up time, so a guaranteed flush window still needs a battery-backed controller or a UPS. Encryption is AES-XTS 256-bit with TCG Opal 2.0 compliance, so self-encrypting deployments and remote locking work on this part.

It is the maximum input the drive will draw at 5 V, not its normal operating figure. Typical draw is 2.3 W reading and 3.0 W writing and 1.4 W idle, all well inside a 6.5 W envelope. The rated current is there so a backplane and its wiring can be sized for the worst case; it is not the number to use when estimating the heat load of a populated chassis.

Samsung PM897 1.92 TB, 2.5-inch 7 mm SATA, catalogue code MZ7L31T9HBNA, ordering code MZ7L31T9HBNA-00B7C. 560 MB/s sequential read, 530 MB/s sequential write, 97K random read and 60K random write IOPS at 4 KB, 10,512 TBW — 3.0 drive-writes-per-day over five years — on Samsung V6 128-layer 3-bit TLC V-NAND, with TCG Opal 2.0 and capacitor-backed power-loss protection. Stocked new or as tested pulls with a 1-year warranty from us.

At 1.92 TB the drive stops being a component and starts being a volume. The 960 GB member holds a datastore or a database; this one holds a datastore and the database, or a single virtualisation host's local storage, or a backup target large enough to be worth restoring from. The performance figures are identical to every other capacity in the range — the only thing that changed is how much work fits on one device, and how long it takes to rebuild if that device fails.

Why this capacity changes what the drive is for

Below 1.92 TB a mixed-use SATA drive is usually one of several devices in a set: a pair of boot drives, a journal on its own spindle, a cache in front of something slower. At 1.92 TB it can be the whole of a small node's storage, and that changes the design conversation. The questions become whether one device is an acceptable failure domain, whether the rebuild fits in the maintenance window, and whether the write budget covers everything the node does rather than one narrow role.

On the first two, the arithmetic is simple and worth doing before the order rather than after. 1.92 TB rebuilt at 530 MB/s takes about an hour of continuous write, which is the same hour during which the array is running degraded and every other member is carrying twice the read load. That is short enough to accept for a two-device mirror and long enough that a larger set is usually the better answer. Ten of these in a RAID set put 19.2 TB behind one parity scheme and turn a single failure into a multi-hour event.

On the third, 10,512 TBW is 5.76 TB of writes a day for five years. That is a node's whole write load, not one application's: a database with its WAL, the hypervisor's swap, container logs and a backup staging area can all sit behind the same 5.76 TB allowance and still leave room. The figure is what makes the "one device per node" design defensible at all.

Technical specifications

Product familySamsung PM897 (V-NAND SSD, data centre / mixed-use)
PNMZ7L31T9HBNA (catalogue code)
Ordering codeMZ7L31T9HBNA-00B7C
Capacity1.92 TB (512-byte sectors, decimal capacity)
Form factor2.5-inch, 7.00 mm (100.20 × 69.85 × 7.00 mm, max 70 g)
InterfaceSATA 6 Gb/s, Serial ATA 3.3, ATA/ATAPI ACS-4
NANDSamsung V6 V-NAND, 128-layer, 3-bit (TLC)
Sequential read / write560 MB/s / 530 MB/s (128 KB, QD32)
Random 4 KB (QD32)97K IOPS read / 60K IOPS write
Random 8 KB (QD32)57K IOPS read / 40K IOPS write
IOPS consistency95% read / 90% write at 4 KB, sustained
Latency and QoS105 µs read / 30 µs write at QD1; 99.99th percentile 0.2 ms read, 0.05 ms write at QD1; 0.6 ms and 0.7 ms at QD32
Endurance10,512 TBW — 3.0 DWPD over five years (TBW = DWPD × 365 × 5 × capacity)
PowerActive read 2.3 W; active write 3.0 W; idle 1.4 W (DIPM off); supply 5 V ±5%, label rated 1.3 A
Power-loss protectionYes — capacitor hold-up transfers cached DRAM data to flash on failure; no hold-up time published
Data securityAES-XTS 256-bit encryption engine, TCG Opal 2.0 compliant
FeaturesTRIM, NCQ to depth 32, S.M.A.R.T., end-to-end data integrity, RoHS
ReliabilityMTBF 2.0 million hours; UBER 1 sector per 1017 bits read
EnvironmentalOperating 0 °C to 70 °C (case); non-operating −40 °C to 85 °C; humidity 5–95% non-condensing

Ordering codes, and what the label records

CodeTypeConditionQuote
MZ7L31T9HBNACatalogue codeNew / usedEnquire
MZ7L31T9HBNA-00B7COrdering codeNew / usedEnquire

The build code changes at this capacity, and it is the one field that will catch a buyer out when a mixed batch arrives. The 480 GB and 960 GB members carry HBLT; this drive and the 3.84 TB member carry HBNA. Both are the same 7 mm 2.5-inch SATA drive on the same firmware line, and both carry the same -00B7C ordering suffix, so the label is what separates them rather than the shape or the connector.

Two other fields on the label are worth reading before a unit goes into service. The rated input is DC 5 V 1.3 A, which is the maximum the drive will draw rather than what it draws in normal operation — the typical figures are 2.3 W reading and 3.0 W writing, well inside that envelope, and the 1.3 A rating is there to size a backplane rather than a power budget. The firmware revision is printed in clear, so a mixed fleet can be checked against the published firmware revision for the part without putting the drive in a host.

The -00B7C suffix is shared across the PM897 range and is not interchangeable with the -00A07 or -00B07 codes, which belong to the read-intensive PM893a and to the PM897a build of this range; those carry different endurance ratings or a different firmware identity. There is no 240 GB and no 7.68 TB PM897, so this and the 3.84 TB member are the top of the range.

Where this drive is not the endurance leader

It is worth saying plainly, because a table of numbers will not say it: at 1.92 TB this is not the highest-endurance SATA drive in the catalogue. The SM863a at 1.92 TB carries 3.5 DWPD and 12,320 TBW, about 17% more write budget on 2-bit MLC, and the PM893 and PM893a make the opposite trade at a third of this drive's endurance.

What the SM863a gives up to carry that budget is throughput: 510/485 MB/s sequential against 560/530 here, and 28K random write against 60K. On a workload that runs a queue — a database commit path, a write-back cache, anything issuing scattered 4 KB writes from several contexts at once — this drive completes more than twice the write operations per second, which is usually worth more than 17% of a write budget that neither drive will exhaust. On a workload that writes steadily and never queues, the SM863a's extra TBW is the better purchase and this page will not pretend otherwise.

What 10,512 TBW buys, and how long a rebuild takes

10,512 TB over five years is 5.76 TB of writes every day. Written flat out at 530 MB/s the rating would last about 230 days, so the ceiling is finite but far outside anything a 1.92 TB volume will produce in normal service. The useful comparison is with the capacity below: this drive carries exactly twice the write budget of the 960 GB member, at the same 3.0 DWPD, because the budget scales with the bytes.

The number that constrains the design at this size is not the write budget, it is the rebuild. At 530 MB/s a full 1.92 TB rewrite takes about an hour, and during that hour a mirrored pair is unprotected and a parity set is running on reduced redundancy. That is the figure to quote when someone proposes consolidating four 480 GB drives into one of these: the consolidation cuts four devices to one, and with them three ports, three firmware records and three idle draws — and it also means a single failure costs an hour of exposure instead of the fifteen minutes a 480 GB rebuild takes.

How 1.92 TB compares with the rest of the Samsung SATA line

ModelCapacitySequential read / writeRandom 4K read / writeEnduranceClass
PM897 1.92 TB1.92 TB560 / 530 MB/s97K / 60K IOPS10,512 TB (3.0 DWPD)Mixed-use
SM883 1.92 TB1.92 TB540 / 520 MB/s97K / 29K IOPS10,512 TB (3.0 DWPD)Mixed-use, MLC
SM863a 1.92 TB1.92 TB510 / 485 MB/s95K / 28K IOPS12,320 TB (3.5 DWPD)Mixed-use, MLC
PM893 1.92 TB1.92 TB550 / 520 MB/s98K / 30K IOPS3,504 TB (1.0 DWPD)Read-intensive
PM893a 1.92 TB1.92 TB560 / 530 MB/s97K / 31K IOPS3,504 TB (1.0 DWPD)Read-intensive
PM883 1.92 TB1.92 TB550 / 520 MB/s98K / 25K IOPS2,733 TB (0.78 DWPD)Read-intensive
PM863a 1.92 TB1.92 TB520 / 480 MB/s97K / 24K IOPS2,733 TB (0.78 DWPD)Read-intensive

Three rows in this table are mixed-use and four are read-intensive, and the gap between the groups is a factor of three on endurance. Within the mixed-use group the ordering is unambiguous on speed and almost reversed on write budget: 60K random write here, 29K on the MLC SM883, 28K on the SM863a. There is no row that wins both, which is the whole point of a portfolio rather than a single part number.

Against the read-intensive group the difference is not marginal. The PM893 and PM893a both carry 3,504 TBW — a third of this drive's budget — and their random read of 98K and 97K matches this drive within a thousand IOPS, which is why they are the correct choice for a volume that is mostly read and the wrong one for a journal. Specifying this drive for a read-only tier spends money on endurance that will never be touched; specifying a read-intensive drive for a continuously written volume is how arrays lose drives early.

How each drive is tested before it ships

Warranty, lead time and purchasing

Every drive carries a 1-year warranty from us against defects in workmanship and function. Verified faulty units are replaced or refunded and we cover return shipping. Stock is held in both new and used condition; the condition you order is confirmed before dispatch, and used units are pull-tested rather than untested lots. Stock is held in our own warehouse and normally dispatches within three to seven working days, with tracking issued at dispatch.

This capacity is quoted rather than listed, because price moves with condition, quantity and batch, and because at 1.92 TB the difference between a low-hour pull and a high-hour one is worth asking about explicitly. Send the quantity, the condition you need and the platform the drives are going into, and you will get a quote with lead time the same working day. Matched sets for mirroring or parity are selected from a single batch where stock allows, including firmware revision and wear level.

Get Pricing For This Part

Tell us who you are — we reply within one working day with a firm quote, stock status and lead time. Volume discounts available.

Prefer email? Write to sales@oceanserverparts.com or WhatsApp +86 13537510010.
Please tell us your name.
A valid email is required.
Need a full RFQ with multiple parts? Use The Full Form →

Related Products

Samsung PM9A3 15.36TB E1.L NVMe SSD (MZEL215THBLA)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 15.36TB E1.L NVMe SSD (MZEL215THBLA)

15.36 TB E1.L 1U long ruler NVMe SSD, PCIe 4.0, ordering code MZEL215THBLA-00AMV

New Used
Request quote
MOQ 2 pc
View
Samsung PM9A3 7.68TB E1.S NVMe SSD (MZCL27T6HBLA)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 7.68TB E1.S NVMe SSD (MZCL27T6HBLA)

7.68 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL27T6HBLA-00AMV / MZTL27T6HBLA-00A07

New Used
Request quote
MOQ 2 pc
View
Samsung PM9A3 3.84TB E1.S NVMe SSD (MZCL23T8HCLS)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 3.84TB E1.S NVMe SSD (MZCL23T8HCLS)

3.84 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL23T8HCLS-00AMV / MZTL23T8HCLS-00A07

New Used
Request quote
MOQ 2 pc
View
Samsung PM9A3 1.92TB E1.S NVMe SSD (MZCL21T9HCJR)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 1.92TB E1.S NVMe SSD (MZCL21T9HCJR)

1.92 TB E1.S 1T (9.5 mm) NVMe SSD, PCIe 4.0, ordering code MZCL21T9HCJR-00AMV

New Used
Request quote
MOQ 2 pc
View