7.68 TB 2.5-inch SATA read-intensive SSD, ordering code MZ7LH7T6HMLA-00005
| Capacity | 7.68 TB |
|---|---|
| Interface | SATA |
| Form Factor | 2.5-inch 7mm |
| PCIe Version | Not applicable |
| NAND Type | TLC |
| Endurance (DWPD) | 0.78 |
| TBW | 10,932 TB |
| Sequential Read | 550 MB/s |
| Sequential Write | 520 MB/s |
| Random Read IOPS | 98K IOPS |
| Random Write IOPS | 27K IOPS |
| Power | 2.3 W |
| DRAM Cache | Yes |
| Power Loss Protection | Yes |
| Encryption | SED |
| Condition | New · Used |
Samsung PM883 7.68 TB, 2.5-inch 7 mm SATA, catalogue code MZ7LH7T6HMLA, ordering code MZ7LH7T6HMLA-00005. 550 MB/s sequential read, 520 MB/s sequential write, 98K random read and 27K random write IOPS, 10,932 TBW on 64-layer 3-bit V-NAND behind a Samsung Maru controller. Stocked new or as tested pulls with a 1-year warranty from us.
This is the capacity Samsung built the PM883 around. 7.68 TB in a 2.5-inch 7 mm slot was the point of the generation — a SATA drive that replaced eight 960 GB drives in the same bay count, at 2.3 W on read and 1.4 W idle, which is less than one spinning disk. Everything below it in the range exists to make this one affordable to build.
The numbers land where the range says they should: 550/520 MB/s, 98K/27K IOPS, 99/90 consistency, and 10,932 TBW — exactly double the 3.84 TB member's 5,466 TB, at an unchanged 0.78 drive-writes-per-day. That is six terabytes of writes a day for five years, which for a read-mostly tier is not a budget anyone will approach; what limits this drive in service is the SATA interface and the rebuild time, not the flash.
The rest of the package is the generation's: 3-bit V-NAND, a Maru controller with a DRAM cache, SATA 3.3 with Power Disable support for per-drive power management, a documented power-loss sequence where tantalum capacitors flush the cache to NAND and the drive is ready within ten seconds, a 2-million-hour MTBF, and no TCG Opal. It is a legacy design — Samsung's current SATA data-centre line is the PM893.
Because bays are the constraint in a lot of installed kit. A 1U server with ten 2.5-inch slots holds 9.6 TB on 960 GB drives and 76.8 TB on these, with the same chassis, the same backplane and the same power envelope — the eightfold density gain comes without a platform refresh. That is the argument for a SATA drive at this capacity in 2026, when a comparable NVMe drive would need U.2 bays the chassis may not have.
Power is part of the same argument, and it is where the numbers are easy to underestimate. Eight 960 GB drives idle at 1.3 W each, so 10.4 W of idle draw for the same capacity this single drive holds at 1.4 W. Under read load it is 2.3 W against 18.4 W. In a rack that number multiplies by the number of servers, which is why dense SATA drives kept selling long after NVMe became faster.
The cost is that everything now depends on fewer devices. A 7.68 TB drive that fails takes eight drives' worth of data with it, and a rebuild on a SATA interface takes hours during which the surviving member or the parity set carries the full load. Plan the redundancy for the capacity, not for the drive count the deployment used to have — and keep a spare, because at this capacity a replacement is not something to source after the failure.
| Product family | Samsung PM883 (V-NAND SSD, data centre / read-intensive) |
|---|---|
| PN | MZ7LH7T6HMLA (catalogue code) |
| Ordering code | MZ7LH7T6HMLA-00005 (General SED) |
| Capacity | 7.68 TB (7,680 GB decimal) |
| Form factor | 2.5-inch, 7.0 mm (100.20 × 69.85 × 6.80 mm, max 70 g) |
| Interface | SATA 6 Gb/s, ATA/ATAPI-7 and Serial ATA 3.3, Power Disable supported |
| Controller | Samsung Maru (Samsung LSI), with DRAM write cache |
| NAND | Samsung V-NAND, 3-bit (TLC), 64-layer; read-intensive over-provisioning |
| Sequential read / write | 550 MB/s / 520 MB/s (128 KB, QD32) |
| Random 4 KB (QD32) | 98K IOPS read / 27K IOPS write |
| IOPS consistency | 99% read / 90% write at 4 KB |
| Latency and QoS | 140 µs read / 40 µs write at QD1; 99.99th percentile 0.5 ms read, 0.3 ms write at QD1; 0.9 ms and 3.2 ms at QD32 |
| Endurance | 10,932 TBW — 0.78 DWPD on a five-year basis; Samsung quotes 1.3 DWPD against a three-year basis, which is the same 10,932 TB |
| Power | Active read 2.3 W; active write 3.6 W; idle 1.4 W; supply 5 V ±5% |
| Power-loss protection | Yes — tantalum capacitor hold-up flushes DRAM to NAND; ready state within 10 s (SPOR). No hold-up time published |
| Data security | AES 256-bit encryption engine (General SED part); no TCG Opal claim |
| Features | TRIM, NCQ to depth 32, S.M.A.R.T., end-to-end data protection, RoHS |
| Reliability | MTBF 2.0 million hours; UBER 1 sector per 1017 bits read; data retention 3 months at 40 °C after rated endurance |
| Environmental | Operating 0 °C to 70 °C (case); non-operating −40 °C to 85 °C; humidity 5–95% non-condensing |
| Shock and vibration | 1,500 G at 0.5 ms half sine; 20 G sine sweep, 20–2,000 Hz |
| Status | Legacy generation — Samsung has discontinued the PM883; supply here is remaining stock and pull-tested units |
| Code | Type | Condition | Quote |
|---|---|---|---|
| MZ7LH7T6HMLA | Catalogue code | New / used | Enquire |
| MZ7LH7T6HMLA-00005 | Ordering code | New / used | Enquire |
The model name follows the family with a different package code at the top: MZ for memory, 7 for the 2.5-inch 7 mm SATA form factor, L for the V-NAND 3-bit line-up where the mixed-use SM883 carries K, H for the Maru controller, 7T6 for 7.68 TB, H for the BGA NAND package, M for first-generation flash, LA for the NAND density code used only at this capacity (the smaller members carry HQ, JR and LT), and -00005 for the General SED customer code. The suffix is a security and packing designation, not a capacity variant, and it is what a PO and a warranty claim are written against.
6.0 TB of writes every day for five years — 5,991 GB at 0.78 drive-writes-per-day, double the 3.84 TB member. Written flat out at 520 MB/s the rating would last about 243 days, which is a long time by the standards of the smaller capacities and still only eight months — the honest way to read it is that 10,932 TB is a large budget for a read-mostly tier and a modest one for a write target.
Samsung rates the PM883 against a three-year basis, so the published figure is 1.3 drive-writes-per-day; spread the same 10,932 TB over five years and it is 0.78, which is how we quote every drive. The arithmetic is exact: 1.3 × 365 × 3 × 7,680 GB = 10,932 TB.
Inside the range the ladder ends here: 341 / 683 / 1,366 / 2,733 / 5,466 / 10,932 TB from 240 GB to 7.68 TB, doubling at every step at an unchanged 0.78 DWPD. The current-generation PM893 at 7.68 TB carries 14,016 TB at 1.0 DWPD and 30K random write — more on both counts, which is what two years of development bought.
The roles are dense and read-dominated: an archive or content tier that is written on ingest and read continuously, a backup restore target written in a window and read for a month, a media library, a scale-out read tier behind a smaller flash cache, a lab or dev environment that wants tens of terabytes of local flash in one chassis. At 7.68 TB the drive is bought for the bay it saves rather than the IOPS it adds, because the IOPS are the same as the 480 GB member's.
Three limits, inherited from the generation. Power-loss protection is capacitor-based and documented but unquantified: the drive flushes its cache and returns to a ready state within ten seconds, but no hold-up time is published, so it does not replace a UPS on anything transactional. There is no TCG Opal 2.0 claim — the -00005 part is a General SED device with the AES 256-bit engine. And the generation is discontinued, which at this capacity is a spares problem more than a supply problem: buy the spare with the tier.
Where endurance matters more than density, the SM883 at 3.84 TB is the largest mixed-use drive Samsung built in this generation, at 21,024 TBW and 3.0 drive-writes-per-day — half the capacity and twice the write budget. Where current-generation credentials matter, the PM893 carries Opal 2.0, a published PLP specification and 14,016 TBW. This drive is the right one when the tier is read-mostly and the bay count is fixed.
| Model | Capacity | Sequential read / write | Random 4K read / write | Endurance | Class |
|---|---|---|---|---|---|
| PM883 480 GB | 480 GB | 550 / 520 MB/s | 98K / 24K IOPS | 683 TB (0.78 DWPD) | Read-intensive |
| PM883 1.92 TB | 1.92 TB | 550 / 520 MB/s | 98K / 25K IOPS | 2,733 TB (0.78 DWPD) | Read-intensive |
| PM883 3.84 TB | 3.84 TB | 550 / 520 MB/s | 98K / 28K IOPS | 5,466 TB (0.78 DWPD) | Read-intensive |
| PM883 7.68 TB | 7.68 TB | 550 / 520 MB/s | 98K / 27K IOPS | 10,932 TB (0.78 DWPD) | Read-intensive |
| SM883 3.84 TB | 3.84 TB | 540 / 520 MB/s | 97K / 29K IOPS | 21,024 TB (3.0 DWPD) | Mixed-use |
| PM893 7.68 TB | 7.68 TB | 550 / 520 MB/s | 98K / 30K IOPS | 14,016 TB (1.0 DWPD) | Read-intensive |
One note on the third and fourth rows, because the two Samsung documents that cover this family disagree there. The OEM specification sheet rates 3.84 TB at 25K random write and 7.68 TB at 27K; a later revision raises 3.84 TB to 28K but does not cover 7.68 TB at all. The table quotes the higher revision where it exists and the OEM sheet for this capacity, which is why the top rung appears 1K below the one beneath it. The difference does not decide a purchase; showing both sources is better than silently picking one.
What the table does show clearly is that this capacity is not a performance purchase. Sequential figures are identical from 480 GB up, random write sits between 24K and 28K at every capacity from 480 GB up, and consistency is 99/90 everywhere. Every step up buys capacity and its proportional write budget — here 7.68 TB and 10,932 TB of it: twice the 3.84 TB read-intensive member, half of what the mixed-use SM883 at 3.84 TB carries at 21,024 TB, and 22% below the current-generation PM893 at the same size.
Every drive carries a 1-year warranty from us against defects in workmanship and function. Verified faulty units are replaced or refunded and we cover return shipping. Stock is held in both new and used condition; the condition you order is confirmed before dispatch, and used units are pull-tested rather than untested lots. Stock is held in our own warehouse and normally dispatches within three to seven working days, with tracking issued at dispatch.
This capacity is quoted rather than listed, because price moves with condition, quantity and which batch the units come from — the PM883 is discontinued, so larger quantities are quoted against confirmed stock rather than a standing lead time. Send the quantity, the condition you need and the server model the drives are going into, and you will get a quote with lead time the same working day. At this capacity we would rather quote a spare alongside the working set than have a rebuild wait on sourcing.
Tell us who you are — we reply within one working day with a firm quote, stock status and lead time. Volume discounts available.
15.36 TB E1.L 1U long ruler NVMe SSD, PCIe 4.0, ordering code MZEL215THBLA-00AMV
7.68 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL27T6HBLA-00AMV / MZTL27T6HBLA-00A07
3.84 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL23T8HCLS-00AMV / MZTL23T8HCLS-00A07
1.92 TB E1.S 1T (9.5 mm) NVMe SSD, PCIe 4.0, ordering code MZCL21T9HCJR-00AMV