15.36 TB 2.5-inch U.2 NVMe SSD, ordering code MZWL915THBLF-00AW7
| Capacity | 15.36 TB |
|---|---|
| Interface | NVMe |
| Form Factor | U.2 15mm |
| PCIe Version | PCIe 5.0 |
| NAND Type | TLC |
| Endurance (DWPD) | 1 |
| TBW | 28,032 TB |
| Sequential Read | 14,000 MB/s |
| Sequential Write | 10,000 MB/s |
| Random Read IOPS | 3,200K IOPS |
| Random Write IOPS | 620K IOPS |
| Power | 20.8 W |
| DRAM Cache | Yes |
| Power Loss Protection | Yes |
| Encryption | AES-XTS 256 |
| Condition | New · Used |
Samsung PM1753 15.36 TB, 2.5-inch U.2 (SFF-8639), catalogue code MZWL915THBLF, supplied under ordering code MZWL915THBLF-00AW7. 14,000 MB/s sequential read, 10,000 MB/s sequential write, 3,200K random read and 620K random write IOPS at 4 KB, 28,032 TBW at one drive write a day over five years, on ninth-generation V-NAND TLC, with AES-XTS 256-bit encryption, power-loss protection and OCP compliance. Stocked new or as tested pulls with a 1-year warranty from us.
This is the 2.5-inch member of the first NVMe family we stock, and it changes what a single bay is worth. A SATA drive in the same 2.5-inch slot tops out near 550 MB/s because that is what SATA 6 Gb/s carries. This one reads at 14,000 MB/s and writes at 10,000 MB/s, which is one drive covering the sequential bandwidth of about twenty-five SATA drives at the same capacity step, without a host bus adapter, a fabric or a second cable run.
Twenty-four 2.5-inch bays holding 15.36 TB drives is 368 TB of raw capacity. Getting the same 368 TB from 7.68 TB SATA drives takes forty-eight bays, so the choice at this capacity point is usually chassis count rather than drive count. What Gen5 adds to that is aggregate bandwidth: twenty-four drives at 14,000 MB/s is a number the PCIe fabric of the host, not the drives, will cap.
The numbers that decide whether that bandwidth is usable are on the random side. 3,200K read IOPS and 620K write IOPS at 4 KB are roughly thirty-three and twenty times what the 7.68 TB SATA drives on this catalogue quote. A workload that is currently served by eight SATA drives per node to reach an IOPS target is usually served by one or two of these, which is where the rack-level saving comes from even before capacity is counted.
Two costs move the other way and are worth stating plainly. Power per drive is higher: 20.5 W reading, 20.8 W writing, against single-digit watts on the SATA parts, so a full shelf of twenty-four draws around 500 W under write load against roughly 100 W idle. And a Gen5 slot is a platform decision: the backplane has to carry PCIe 5.0, the cable and the retimer budget have to be right, and a Gen4 host will train this drive down to Gen4 speeds without complaining.
| Product family | Samsung PM1753 (PCIe 5.0 enterprise NVMe SSD) |
|---|---|
| PN | MZWL915THBLF (catalogue code) |
| Ordering code | MZWL915THBLF-00AW7 |
| Capacity | 15.36 TB (unformatted; 1 GB = 1 billion bytes, formatted capacity is less) |
| Form factor | 2.5-inch U.2, SFF-8639, 15 mm (100.20 × 69.85 × 15.00 mm) |
| Interface | PCIe 5.0 x4, NVMe 2.0, dual-port capable through the U.2 connector |
| NAND | Samsung ninth-generation V-NAND TLC |
| Sequential read / write | 14,000 MB/s / 10,000 MB/s |
| Random 4 KB | 3,200K IOPS read / 620K IOPS write |
| Endurance | 28,032 TBW — 1 DWPD over five years |
| TBW basis | Drive held full under a sequential write workload over the five-year rating period |
| Power | 20.5 W reading, 20.8 W writing, 4 W idle |
| Power-loss protection | Yes — integrated PLP with capacitor health reported by firmware |
| Data security | AES-XTS 256-bit encryption, secure erase, TCG security subsystem |
| DRAM cache | Yes |
| Features | PLP, end-to-end data protection, S.M.A.R.T., OCP 2.0 compliance, hot-plug, sanitize and secure erase |
| Reliability | MTBF 2.5 million hours; UBER under 1 sector per 1017 bits read |
| Environmental | Operating 0 °C to 70 °C case temperature; non-operating −40 °C to 85 °C |
28,032 TB over five years is 15,360 GB of writes every day, exactly one fill of the drive. Written flat out at 10,000 MB/s the whole allowance would last about 32 days; the rating spreads it across 1,825 days instead, which is the same arithmetic every enterprise drive uses. A volume rewriting a fifth of its capacity daily uses 20% of the allowance; a log partition writing 200 GB a day uses 1.3%.
What is different at this capacity is how much writing a single fill represents. One DWPD on 15.36 TB is 15.36 TB a day, which is exactly what two 7.68 TB drives at their own one-fill ratings would write between them, and it comes from a single bay. That is the practical case for buying density on a write-heavy volume: the rating is the same percentage, but the bytes behind it are doubled.
A full rebuild at 10,000 MB/s takes about 26 minutes of pure transfer, against roughly four hours for the 7.68 TB SATA drives at 520 MB/s. Real rebuild time will be longer than the transfer figure because the controller and the host fabric share the bandwidth, but the order of magnitude is what changes the recovery plan: a shelf that took a working day to rebuild is now a coffee break, which is often worth more than the throughput.
| Code | Type | Capacity | Condition | Quote |
|---|---|---|---|---|
| MZWL915THBLF | Catalogue code | 15.36 TB | New / used | Enquire |
| MZWL915THBLF-00AW7 | Ordering code | 15.36 TB | New / used | Enquire |
The model string follows Samsung's NVMe convention rather than the SATA one, and the two parts worth reading are the prefix and the capacity block. MZW is the prefix used for this family of NVMe solid-state drives, and 15T inside the string is the capacity block: 15T is 15.36 TB, 7T6 is 7.68 TB, 3T8 is 3.84 TB and 1T9 is 1.92 TB. The -00AW7 suffix is the build and channel block, which is where OEM variants and firmware channels differ.
Two things follow for a buyer. A drive pulled from a server may carry the OEM's own label on the outside with the Samsung string in the model field, so the field rather than the branding is what identifies it. And because the capacity block sits inside the model string rather than on a separate line, two drives whose labels look identical at a glance can differ by a factor of two in capacity.
This part is the 2.5-inch build. The same drive is also stocked in the E3.S form factor, which fits twenty units in 1U against ten for this one and carries the same 28,032 TBW.
| Model | Interface | Capacity | Seq read / write | Random 4 KB | TBW | DWPD |
|---|---|---|---|---|---|---|
| PM1753 15.36 TB | PCIe 5.0 x4 | 15.36 TB | 14,000 / 10,000 MB/s | 3,200K / 620K | 28,032 TB | 1 |
| PM893a 7.68 TB | SATA 6 Gb/s | 7.68 TB | 560 / 530 MB/s | 97K / 31K | 14,016 TB | 1 |
| PM883 7.68 TB | SATA 6 Gb/s | 7.68 TB | 550 / 520 MB/s | 98K / 27K | 10,932 TB | 0.78 |
| 5200 ECO 7.68 TB | SATA 6 Gb/s | 7.68 TB | 540 / 520 MB/s | 95K / 9.5K | 8,400 TB | 0.6 |
The comparison is not a like-for-like price argument, because the interface decides what the drive can be plugged into. Read it as a statement about where the money goes. Against the closest SATA part on endurance, the PM893a 7.68 TB, this drive carries twice the capacity and twice the total write budget at the same one-fill rating, twenty-five times the sequential read and thirty-three times the random read. Against the read-intensive SATA parts the split is wider still on random write: 620K against 9.5K on the 5200 ECO 7.68 TB is the difference between a tier and a generation boundary.
Where SATA still wins is the cost of entry per terabyte and the cost of the slot around it. A Gen5 backplane, retimers and a host that can drive four lanes at 32 GT/s are all part of the purchase, and none of them appear on a drive quotation. For a fleet that is already built around SATA, the honest answer is that this drive is a platform change, not a disk swap.
SATA 6 Gb/s carries about 600 MB/s of signalling and delivers roughly 550 MB/s after protocol overhead, which is why every SATA drive on this catalogue writes between 520 and 530 MB/s regardless of tier, generation or price. The limit is the bus, and it does not move with better NAND or a better controller.
PCIe 5.0 x4 is a different order of magnitude: 32 GT/s per lane across four lanes, which is why this drive quotes 14,000 MB/s and why the same capacity on Gen4 stops near 7,000 MB/s. Nothing about the NAND changes between those two numbers; the link does. That is also why a Gen5 drive in a Gen4 slot is not a failed purchase, only a slower one: it negotiates down and runs at the ceiling of the slot it is in.
Every drive is listed after inspection rather than before: label fields recorded, SMART read and kept against the unit, a full-surface read scan, the drive's own self-test run to completion, sequential and random performance measured on a native PCIe 5.0 port, latency sampled at queue depth one, and a secure erase before packing. Stock normally leaves our warehouse within three to seven working days, with tracking issued at dispatch.
Current capacity and interface availability is in the enterprise SSD catalog. If you are weighing NVMe against a SATA rebuild, the read-intensive versus mixed-use guide covers how the endurance tiers are set and where the write budget stops doubling. Send us the platform, the slot count and the workload, and we will say whether Gen5 pays on your chassis or whether the money is better spent on more SATA bays.
Tell us who you are — we reply within one working day with a firm quote, stock status and lead time. Volume discounts available.
15.36 TB E1.L 1U long ruler NVMe SSD, PCIe 4.0, ordering code MZEL215THBLA-00AMV
7.68 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL27T6HBLA-00AMV / MZTL27T6HBLA-00A07
3.84 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL23T8HCLS-00AMV / MZTL23T8HCLS-00A07
1.92 TB E1.S 1T (9.5 mm) NVMe SSD, PCIe 4.0, ordering code MZCL21T9HCJR-00AMV