Dispatch in 3–7 working days · 1-year warranty on every part Call A Rep: +86 13537510010 | Request A Quote
Inspected & Load-Tested Before Dispatch Serial Recorded Dispatch in 3–7 working days
MTFDDAK7T6TDC · Micron

Micron 5200 ECO 7.68TB SATA SSD (MTFDDAK7T6TDC)

7.68 TB 2.5-inch SATA read-intensive SSD, ordering codes MTFDDAK7T6TDC-1AT1ZABYY and -1AT16ABYY

New Used
Pricing Request quote
MOQ 2 pc · volume pricing on request
Reply Within 24h
Volume Pricing
Worldwide Shipping
Secure Anti-Static Pack
Part Number
MTFDDAK7T6TDC
Brand
Micron
Category
Enterprise & Data Center SSD
Accepted Payments
T/T Bank Transfer PayPal Western Union

Technical Specifications

Capacity 7.68 TB
Interface SATA
Form Factor 2.5-inch 7mm
PCIe Version Not applicable
NAND Type TLC
Endurance (DWPD) 0.6
TBW 8,400 TB
Sequential Read 540 MB/s
Sequential Write 520 MB/s
Random Read IOPS 95K IOPS
Random Write IOPS 9.5K IOPS
Power 3.6 W
DRAM Cache Yes
Power Loss Protection Yes
Encryption TCG Enterprise
Condition New · Used

Frequently Asked Questions

The catalogue code is MTFDDAK7T6TDC and we supply two ordering codes at this capacity, MTFDDAK7T6TDC-1AT1ZABYY and MTFDDAK7T6TDC-1AT16ABYY. MTFDDAK is the prefix for Micron SATA drives in the 2.5-inch 7 mm form factor, 7T6 is the 7.68 TB capacity block and TDC is the 5200 ECO tier. The two codes differ by one character inside the configuration block.

Because 8,400 TB over five years is 4,603 GB a day against 7,680 GB of capacity, which is 0.6 of a fill. The budget stops doubling at the top of the range: 7,700 TB at 3.84 TB becomes 8,400 TB here on twice the bytes, so the ratio falls even though the absolute number rises. A volume writing more than 4.6 TB a day should use the tier above rather than this drive.

Fit twice the data in one 7 mm bay. Twenty-four drives give 184 TB at 36 W idle and 86 W at the worst case, which is 0.47 W per terabyte, and it takes half the bays, cables, firmware records and rebuild events of the same capacity built from 3.84 TB drives. What it does not do is match that drive on endurance, random write or write latency.

It is the lowest figure in this family and below every other 7.68 TB drive we list, so it is a problem for any volume with a sustained write queue: database logs, recording buffers, container registries and backup targets all fit that description. For a read-mostly volume it never appears, because random write only shows up when the drive is actually taking small concurrent writes.

Very little, and less than at any other capacity. Both quote 540/520 MB/s, both carry 8,400 TBW at 0.6 drive writes a day, and random read and write differ by 2K and half a thousand IOPS. The quoted power figures differ, 3.6 W maximum here against 6 W typical there, but they are not measured the same way. Choose on condition and price, and check the model number on the label.

A data-protection capacitor with firmware monitoring holds the drive up long enough to commit acknowledged writes when power drops. The drive carries AES 256-bit encryption with TCG Enterprise enabled through the controller, and self-encrypting builds are separate ordering configurations. If a platform requires encryption at rest, specify the self-encrypting block rather than assuming the standard code arrives enabled.

Micron 5200 ECO 7.68 TB, 2.5-inch 7 mm SATA, catalogue code MTFDDAK7T6TDC, supplied under ordering codes MTFDDAK7T6TDC-1AT1ZABYY and MTFDDAK7T6TDC-1AT16ABYY. 540 MB/s sequential read, 520 MB/s sequential write, 95K random read and 9.5K random write IOPS at 4 KB, 8,400 TBW at 0.6 drive writes a day, on Micron 64-layer 3D TLC, with 200 µs read and 900 µs write latency at the 99.9th percentile and capacitor-backed power-loss protection. Stocked new or as tested pulls with a 1-year warranty from us.

This is the top of the range and the one capacity where the tier's arithmetic works against it. Doubling from 3.84 TB buys 9% more write budget, not 100%, and the rating falls from 1.1 drive writes a day to 0.6. What it buys instead is density: 7.68 TB in a single 7 mm bay at the same 3.6 W maximum the 3.84 TB member draws. Buy it for bytes per bay, not for endurance or small-block write, and it is a sound drive.

What 7.68 TB is for, and what it is not

The case for this capacity is entirely about what fits in a chassis. Twenty-four of these in a 2U shelf is 184 TB of raw read-intensive capacity at 36 W idle and 86 W if every drive were writing at once, which is 0.47 W per terabyte at the worst case. Getting the same 184 TB from 3.84 TB drives takes twice the bays, twice the cables, twice the firmware records and twice the rebuild events, and at 184 TB the bays are usually the scarce resource.

What it is not is a drive for anything that writes hard. Random write is 9.5K at 4 KB, the lowest figure in this family and below every other 7.68 TB drive we list; the 99.9th percentile write latency is 900 µs, three times the 300 µs the smaller members quote; and the rating is 0.6 fills a day. A volume with a write queue, a database log, a recording buffer or a container registry belongs on the mixed-use tier, where the same 540/520 MB/s comes with several times these figures.

The read side, by contrast, is indistinguishable from the rest of the tier: 540 MB/s sequential, 95K random read and 200 µs at the 99.9th percentile, exactly what the 960 GB and 1.92 TB members quote. That asymmetry is the whole specification in one line — the tier's read performance is flat across five capacities and everything else degrades as the bytes grow.

Technical specifications

Product familyMicron 5200 ECO (SATA NAND Flash SSD, read-intensive data centre)
PNMTFDDAK7T6TDC (catalogue code)
Ordering codesMTFDDAK7T6TDC-1AT1ZABYY and MTFDDAK7T6TDC-1AT16ABYY
Capacity7.68 TB (unformatted; 1 GB = 1 billion bytes, formatted capacity is less)
Form factor2.5-inch, 7 mm (100.45 × 69.85 × 7.00 mm)
InterfaceSATA 6 Gb/s, ATA-8 ACS-3, hot-plug capable, NCQ to depth 32
NANDMicron 64-layer 3D TLC
Sequential read / write540 MB/s / 520 MB/s (128 KB, steady state)
Random 4 KB (QD32)95K IOPS read / 9.5K IOPS write
Quality of service200 µs read / 900 µs write at the 99.9th percentile
Endurance8,400 TBW — 0.6 DWPD over five years
TBW basisDrive held full under a random write workload over the five-year rating period
Power3.6 W maximum on sequential write, 3.0 W maximum on sequential read, 1.5 W idle
Power-loss protectionYes — data-protection capacitor with capacitor monitoring reported by firmware
Data securityAES 256-bit encryption, TCG Enterprise enabled through the controller; self-encrypting configurations carry their own ordering blocks
DRAM cacheYes
FeaturesFlex Capacity, end-to-end data path protection, adaptive thermal monitoring, RAIN recovery, S.M.A.R.T., secure and fast erase, secure firmware
ReliabilityMTTF 3.0 million device hours; UBER under 1 sector per 1017 bits read
EnvironmentalOperating 0 °C to 70 °C; non-operating shock 1500G at 0.5 ms; vibration 3.13G RMS at 5–800 Hz

The turn at the top of the range, and what it does to the generation

Across the family the write budget doubles with the bytes until it does not. 870, 1,750, 3,500 and 7,700 TB track 480 GB, 960 GB, 1.92 TB and 3.84 TB almost exactly, so the rating holds near a fill a day and even rises to 1.1 at 3.84 TB. Then this capacity arrives with 8,400 TB on twice those bytes: 9% more budget for 100% more capacity, and a rating that drops to 0.6 — the only member of the family below one fill a day.

The cause is visible in the arithmetic rather than in the marketing. Doubling capacity doubles the daily write a one-fill rating implies, and 8,400 TB cannot cover 7.68 TB a day for five years; it covers 4,603 GB, which is 0.6 of that. Micron chose to keep the absolute budget roughly in step with the previous capacity instead of doubling it, and the rating is what records that decision.

For a buyer the consequence is simple to state. If the volume writes less than 4.6 TB a day, this drive is comfortably inside its rating and the density case above carries. If it writes more, no amount of spare bays fixes it and the answer is the tier above at the same capacity, or two smaller drives in the tier that rates higher. The 3.84 TB member is the one that keeps the better ratio, at 1.1.

The ECO tier of this generation runs 480 GB, 960 GB, 1.92 TB, 3.84 TB and 7.68 TB, and this is the last of them. Read performance across the five is flat at 540 MB/s, 95K random read and 200 µs, with one exception at 480 GB where both sequential write and random read sit lower. Sequential write reaches 520 MB/s at 960 GB and holds. Random write slides the whole length: 33K, 28K, 22K, 17K and 9.5K, and write latency at the 99.9th percentile rises at the top end: 300, 300, 300, 500 and 900 µs.

The generational comparison changes character at this size, and that is the most useful thing on this page after the density case. Against the 5100 ECO 7.68 TB the two drives are nearly the same specification: 540/520 MB/s on both, the same 8,400 TBW, the same 0.6 rating, and random read and write within 2K and half a thousand IOPS of each other. What separates them is the quoted power figure — 3.6 W maximum here against 6 W typical there, which are not measured the same way — and almost nothing else.

At 480 GB and 960 GB this generation was worth choosing on endurance alone, at 93% and 94% more budget. At 7.68 TB that argument is gone. Buy whichever of the two is in better condition or better priced, and check the label rather than the tier name, because the two share a capacity, a case, a connector and a performance envelope.

What 8,400 TBW means at 7.68 TB

8,400 TB over five years is 4,603 GB of writes every day, 0.6 fills of the drive. Written flat out at 520 MB/s the whole allowance would last about 187 days; the rating assumes that daily allowance spread across 1,825 days instead. A boot and log pair writing 80 GB a day uses 2% of the allowance. A cache that rewrites a fifth of its capacity daily is a different matter at this size: 1,536 GB a day is 33% of the allowance, so the same cache policy that sits at 18% on the 3.84 TB member uses nearly twice the share here.

That last comparison is the one worth carrying into a design review. Endurance policy is usually written as a percentage of capacity — rewrite a fifth of the volume daily, keep three copies of a dataset — and every such policy costs more of the allowance as the drive gets larger while the allowance here has hardly grown. A 7.68 TB volume on a policy that was tuned on 1.92 TB drives should be re-checked rather than assumed.

A full rebuild at 520 MB/s takes about four hours, against two for the 3.84 TB member, which is the other number that changes when capacity doubles on the same interface. Where recovery time is written into a service level, four hours of degraded redundancy per drive is a real constraint and worth modelling before the shelf is built.

Ordering codes and the generation block

CodeTypeConditionQuote
MTFDDAK7T6TDCCatalogue codeNew / usedEnquire
MTFDDAK7T6TDC-1AT1ZABYYOrdering codeNew / usedEnquire
MTFDDAK7T6TDC-1AT16ABYYOrdering codeNew / usedEnquire

The model number is the stable part. MTFDDAK is the prefix Micron uses for SATA solid-state drives in this form factor, 7T6 is the 7.68 TB capacity block, and TDC is the 5200 ECO tier; the family uses TDD for PRO and TDN for MAX. Everything after TDC belongs to the configuration block, which is where the two codes we list diverge by a single character, and where self-encrypting builds and OEM channels apply patterns of their own.

Read the capacity block with care, because Micron writes terabyte capacities in decimal shorthand: 1T9 is 1.92 TB, 3T8 is 3.84 TB and 7T6 is 7.68 TB, while 480 and 960 are written as plain digits. At this capacity the mistake that bites is not the digit itself but the assumption that a bigger number is visible: the case, the label layout and the connector are the same across every capacity in the family, so the model field and the label are the only things separating a 7.68 TB unit from a 3.84 TB one.

How it compares across the 7.68 TB SATA line

ModelCapacitySequential read / writeRandom 4K read / writeEndurancePowerClass
Micron 5200 ECO 7.68 TB7.68 TB540 / 520 MB/s95K / 9.5K IOPS8,400 TB (0.6 DWPD)3.6 W maxRead-intensive, 64-layer TLC
Micron 5100 ECO 7.68 TB7.68 TB540 / 520 MB/s93K / 9K IOPS8,400 TB (0.6 DWPD)6 W typRead-intensive, 32-layer TLC
Samsung PM893a 7.68 TB7.68 TB560 / 530 MB/s97K / 31K IOPS14,016 TB (1.0 DWPD)2.2 WRead-intensive, TLC
Samsung PM893 7.68 TB7.68 TB550 / 520 MB/s98K / 30K IOPS14,016 TB (1.0 DWPD)3.2 WRead-intensive, TLC
Samsung PM883 7.68 TB7.68 TB550 / 520 MB/s98K / 27K IOPS10,932 TB (0.78 DWPD)2.3 WRead-intensive, TLC

Read straight across, and the column that decides the purchase is the endurance one. This drive is last on write budget at 8,400 TB, level with the 5100 ECO and 40% below the 14,016 TB the two PM893 rows carry, which is the widest gap between this generation and the Samsung read-intensive line anywhere in the range. It is also fourth on random write at 9.5K, above only the 5100 ECO's 9K and far below the 27K to 31K the Samsung rows quote.

On the read side it holds up better. It is third on random read at 95K, behind 97K and 98K, and 2K above the 5100 ECO; joint fourth on sequential read at 540 MB/s, level with the 5100 ECO and behind the 550 and 560 rows; and second on sequential write at 520 MB/s, level with three rows and behind only the 530 of the PM893a. On the quoted power figure it is second highest at 3.6 W, though that is a maximum against the typical figures the Micron tier above quotes.

The honest summary is that this is the weakest 7.68 TB drive on the page for anything other than reading and storing. Against the PM893a it gives up 20 MB/s of read, 10 MB/s of write, 2K of random read, 21.5K of random write and 40% of the write budget, and takes back nothing except a lower quoted maximum on power. What it does have is the lowest power per terabyte at idle in a shelf and full TCG Enterprise configurability, and where the workload really is read-only, none of those losses show up.

How each drive is tested before it ships

Warranty, lead time and purchasing

Every drive carries a 1-year warranty from us against defects in workmanship and function. Verified faulty units are replaced or refunded and we cover return shipping. Stock is held in both new and used condition; the condition you order is confirmed before dispatch, and used units are pull-tested rather than untested lots. Stock is held in our own warehouse and normally dispatches within three to seven working days, with tracking issued at dispatch.

This capacity is quoted rather than listed, because price moves with condition, quantity and batch, and 7.68 TB drives change hands in smaller volumes than the 960 GB and 1.92 TB sizes. Send the quantity, the condition you need, the ordering code your build specifies where it does, the platform the drives are going into and the shelf size you are filling, and you will get a quote with lead time the same working day.

Get Pricing For This Part

Tell us who you are — we reply within one working day with a firm quote, stock status and lead time. Volume discounts available.

Prefer email? Write to sales@oceanserverparts.com or WhatsApp +86 13537510010.
Please tell us your name.
A valid email is required.
Need a full RFQ with multiple parts? Use The Full Form →

Related Products

Samsung PM9A3 15.36TB E1.L NVMe SSD (MZEL215THBLA)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 15.36TB E1.L NVMe SSD (MZEL215THBLA)

15.36 TB E1.L 1U long ruler NVMe SSD, PCIe 4.0, ordering code MZEL215THBLA-00AMV

New Used
Request quote
MOQ 2 pc
View
Samsung PM9A3 7.68TB E1.S NVMe SSD (MZCL27T6HBLA)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 7.68TB E1.S NVMe SSD (MZCL27T6HBLA)

7.68 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL27T6HBLA-00AMV / MZTL27T6HBLA-00A07

New Used
Request quote
MOQ 2 pc
View
Samsung PM9A3 3.84TB E1.S NVMe SSD (MZCL23T8HCLS)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 3.84TB E1.S NVMe SSD (MZCL23T8HCLS)

3.84 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL23T8HCLS-00AMV / MZTL23T8HCLS-00A07

New Used
Request quote
MOQ 2 pc
View
Samsung PM9A3 1.92TB E1.S NVMe SSD (MZCL21T9HCJR)
Samsung · Enterprise & Data Center SSD
Samsung PM9A3 1.92TB E1.S NVMe SSD (MZCL21T9HCJR)

1.92 TB E1.S 1T (9.5 mm) NVMe SSD, PCIe 4.0, ordering code MZCL21T9HCJR-00AMV

New Used
Request quote
MOQ 2 pc
View