120 GB 2.5-inch SATA read-intensive SSD, ordering code MTFDDAK120MBP-1AN1ZABYY
| Capacity | 120 GB |
|---|---|
| Interface | SATA |
| Form Factor | 2.5-inch 7mm |
| PCIe Version | Not applicable |
| NAND Type | MLC |
| Endurance (DWPD) | 2.1 |
| TBW | 460 TB |
| Sequential Read | 420 MB/s |
| Sequential Write | 170 MB/s |
| Random Read IOPS | 63K IOPS |
| Random Write IOPS | 12K IOPS |
| Power | 4 W |
| DRAM Cache | Yes |
| Power Loss Protection | Yes |
| Encryption | TCG Enterprise |
| Condition | New · Used |
Micron M510DC 120 GB, 2.5-inch 7 mm SATA, catalogue code MTFDDAK120MBP, ordering code MTFDDAK120MBP-1AN1ZABYY. 420 MB/s sequential read, 170 MB/s sequential write, 63K random read and 12K random write IOPS at 4 KB, 460 TBW on Micron 16nm MLC NAND, with a data-protection capacitor, TCG Enterprise self-encryption and end-to-end data path protection. Stocked new or as tested pulls with a 1-year warranty from us.
Two numbers on this page look wrong next to each other, and both are right. The 170 MB/s sequential write is the slowest in the M510DC range, because a 120 GB drive has the fewest NAND die to write across in parallel. The 460 TBW is larger than the write budget of most 240 GB read-intensive drives on this site, including the Samsung PM893 at that capacity. Small capacity here means lower peak write speed, not a shorter working life, and the rest of this page is about which of the two matters for the job in front of you.
The range shares one sequential read figure, 420 MB/s, at every capacity. Write is where the capacities separate: 170 MB/s at 120 GB, 290 at 240 GB, then 380 from 480 GB upward. Random write follows a different curve — 12K, 18K, 23K, then 10.5K at 960 GB — because the 960 GB member is rated at one drive fill a day instead of two, and its endurance rating, not its die count, sets that number. So this drive is last on sequential write and second to last on random write, above only the 960 GB part.
What that costs in practice depends entirely on the queue. A boot volume, a hypervisor system partition, a proxy cache or a log staging area reads far more than it writes, and 170 MB/s is enough for all of them: the drive still serves 420 MB/s and 63K random reads, which is the traffic those roles actually generate. Put it in a write path that never drains — a database data volume, a backup target, a surveillance recorder — and the 170 MB/s ceiling becomes the bottleneck long before the 460 TBW does.
There is one more consequence worth stating plainly. Because the endurance rating is fixed by Micron rather than derived from capacity, the ratio of write budget to write speed is unusual at this size: written flat out at 170 MB/s, the entire 460 TB rating is consumed in about 31 days. That is not a warning about the drive; it is a reminder that the endurance figure assumes a daily allowance spread over five years, and that any drive run at its ceiling finishes its rating quickly.
| Product family | Micron M510DC (SATA NAND Flash SSD, read-intensive data centre) |
|---|---|
| PN | MTFDDAK120MBP (catalogue code) |
| Ordering code | MTFDDAK120MBP-1AN1ZABYY |
| Capacity | 120 GB (unformatted; 1 GB = 1 billion bytes, formatted capacity is less) |
| Form factor | 2.5-inch, 7 mm (69.85 × 100.45 × 7.00 mm) |
| Interface | SATA 6 Gb/s, ATA-8 ACS2, hot-plug capable, NCQ to depth 32 |
| NAND | Micron 16nm MLC NAND |
| Sequential read / write | 420 MB/s / 170 MB/s (128 KB, steady state) |
| Random 4 KB (QD32) | 63K IOPS read / 12K IOPS write |
| Latency | 0.50 ms read / 3.0 ms write (typical) |
| Endurance | 460 TBW — 2.1 DWPD over five years, which Micron states as 2 drive fills a day (1 drive fill/day at 960 GB) |
| TBW basis | 55 °C case temperature, drive 100% full, 100% random aligned 4 KB writes |
| Power | Idle 1.2 W; sequential write max 4 W; sequential read max under 4 W; active average 1.5 W |
| Power-loss protection | Yes — data-protection capacitor, with capacitor monitoring reported by firmware |
| Data security | TCG Enterprise 1.0 SED (self-encrypting drive); AES encryption engine |
| DRAM cache | Yes — on-board DDR3 DRAM |
| Features | XPERT feature set: data path protection, adaptive thermal monitoring, power-loss protection; static and dynamic wear levelling; end-to-end data protection |
| Reliability | MTTF 2.0 million device hours; UBER under 1 sector per 1016 bits read |
| Environmental | Operating 0 °C to 70 °C (case); non-operating −40 °C to 85 °C; humidity 5–95% non-condensing; operating shock 1500G/0.5 ms; vibration 10–500 Hz at 3.1G |
| Code | Type | Condition | Quote |
|---|---|---|---|
| MTFDDAK120MBP | Catalogue code | New / used | Enquire |
| MTFDDAK120MBP-1AN1ZABYY | Ordering code | New / used | Enquire |
The part number decodes by position. MTFDDAK is the prefix Micron uses for its SATA solid-state drives in this form factor, 120 is the capacity in gigabytes, MBP identifies the M510DC family in a 2.5-inch 7 mm case, and everything after the hyphen is the configuration string Micron assigns at order entry. That suffix covers interface options, firmware and customer identity, and Micron does not publish a public field-by-field decode for it, so we quote it in full rather than guess at its parts.
The practical point is that MTFDDAK120MBP and MTFDDAK240MBP differ by one three-digit block and by nothing else in the model number. If a PO line says 120 and a 240 GB drive arrives, the model number and the capacity line on the label are the only two places it shows, and the two drives are physically identical in the hand. Read the digits, not the family name.
460 TB over five years is 252 GB of writes every day. For a 120 GB drive that is two full fills a day, which is exactly how Micron states the rating — two drive fills per day at 120, 240 and 480 GB, one at 960 GB. The TBW figure is calculated at a 55 °C case temperature with the drive 100% full under 100% random aligned 4 KB writes, which is a harsher basis than a sequential workload and is why the number looks generous for the capacity.
Set beside the nearest alternative on this site, the Samsung PM893 at 240 GB, the comparison is not the one capacity would suggest. The Samsung drive is rated 1.0 drive fill a day and 438 TBW; this one is rated two fills a day and 460 TBW, on half the bytes. If the requirement is a small volume that gets rewritten daily, this drive carries about 5% more write budget than a 240 GB read-intensive part while occupying half the space and drawing 1.2 W at idle.
What it does not carry is throughput. The PM893 does 550/380 MB/s and 98K/15K IOPS against 420/170 and 63K/12K here. So the choice at this size is not endurance against endurance — it is whether the workload is limited by how much can be written in total or by how fast it can be written now. Very few 120 GB volumes are limited by the first.
Three roles fit it well. A mirrored boot pair in a server that keeps its data elsewhere, where the alternative is a consumer drive without power-loss protection or self-encryption. A hypervisor system partition that is read at every boot and written to only by configuration changes. And an appliance — firewall, proxy, monitoring collector, backup catalog — where the operating system and its logs live on the drive and the capacity requirement is genuinely small.
Two roles do not fit it, and both are common enough to name. A database or log volume that writes continuously will be limited by 170 MB/s rather than by endurance, and a 120 GB capacity gives a log volume very little room to absorb a burst. A surveillance or media-cache tier writes far more per day than two fills and should not be built on this capacity at all.
The enterprise features are what separate this drive from a consumer SATA part at the same size, and they remain the reason to buy it used rather than buy new consumer hardware. The data-protection capacitor holds the drive up long enough to commit writes already acknowledged when power drops, and firmware reports capacitor health through SMART. TCG Enterprise encryption is a different scheme from the consumer TCG Opal 2.0 used on most SATA SSDs: it needs a controller or key-management stack that speaks TCG Enterprise, so confirm the host supports it before relying on it, and check that a used drive is not still locked to a previous owner's keys.
| Model | Capacity | Sequential read / write | Random 4K read / write | Endurance | Class |
|---|---|---|---|---|---|
| Micron M510DC 120 GB | 120 GB | 420 / 170 MB/s | 63K / 12K IOPS | 460 TB (2.1 DWPD) | Read-intensive, 16nm MLC |
| Micron M510DC 240 GB | 240 GB | 420 / 290 MB/s | 63K / 18K IOPS | 920 TB (2.1 DWPD) | Read-intensive, same family |
| Samsung PM893 240 GB | 240 GB | 550 / 380 MB/s | 98K / 15K IOPS | 438 TB (1.0 DWPD) | Read-intensive, TLC |
| Samsung PM883 240 GB | 240 GB | 550 / 320 MB/s | 98K / 14K IOPS | 341 TB (0.78 DWPD) | Read-intensive, TLC |
| Samsung PM863a 240 GB | 240 GB | 330 / 300 MB/s | 86K / 9K IOPS | 341 TB (0.78 DWPD) | Read-intensive, TLC |
| Samsung SM863a 240 GB | 240 GB | 410 / 450 MB/s | 90K / 10K IOPS | 1,540 TB (3.5 DWPD) | Mixed-use, MLC |
| Samsung SM883 240 GB | 240 GB | 540 / 480 MB/s | 97K / 22K IOPS | 1,314 TB (3.0 DWPD) | Mixed-use, MLC |
The table spans two capacity points because 120 GB is a segment where this site currently lists one enterprise drive, and the 240 GB parts are what a buyer would otherwise be choosing between. Read across the endurance column first: this drive's 460 TB beats all three of the 240 GB read-intensive parts and sits 5% above the PM893, while the two mixed-use MLC drives at 1,314 and 1,540 TB are the only ones that clearly outlast it.
Read across the performance columns second, and the ordering reverses. Every 240 GB part on this list writes sequentially faster than 170 MB/s, from 300 MB/s on the PM863a up to 480 MB/s on the SM883, and all five serve more random reads. So the trade is straightforward: half the bytes and a lower write ceiling against a write budget that is competitive at twice the capacity. If the volume is small and rewritten, this drive makes sense; if the volume is small and read, the extra read throughput of a 240 GB part is worth the space it wastes.
Every drive carries a 1-year warranty from us against defects in workmanship and function. Verified faulty units are replaced or refunded and we cover return shipping. Stock is held in both new and used condition; the condition you order is confirmed before dispatch, and used units are pull-tested rather than untested lots. Stock is held in our own warehouse and normally dispatches within three to seven working days, with tracking issued at dispatch.
This capacity is quoted rather than listed, because price moves with condition, quantity and batch. Send the quantity, the condition you need and the platform the drives are going into, and you will get a quote with lead time the same working day. If the host uses TCG Enterprise key management, say so when you enquire and we will confirm the drive's security state before it ships; matched pairs for a boot mirror are selected from a single batch where stock allows, including firmware revision and wear level.
Tell us who you are — we reply within one working day with a firm quote, stock status and lead time. Volume discounts available.
15.36 TB E1.L 1U long ruler NVMe SSD, PCIe 4.0, ordering code MZEL215THBLA-00AMV
7.68 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL27T6HBLA-00AMV / MZTL27T6HBLA-00A07
3.84 TB E1.S 1T NVMe SSD, PCIe 4.0, ordering codes MZCL23T8HCLS-00AMV / MZTL23T8HCLS-00A07
1.92 TB E1.S 1T (9.5 mm) NVMe SSD, PCIe 4.0, ordering code MZCL21T9HCJR-00AMV