8 GB DDR4-2133 PC4-17000 ECC registered RDIMM, 1Rx4, 1.2 V, 288-pin; nine ordering codes from M393A1G40EB1-CPB0 to -CPBQ
| Capacity | 8 GB |
|---|---|
| Memory Type | DDR4 |
| Speed | 2133 MT/s |
| Form Factor | RDIMM |
| Rank | 1Rx4 |
| ECC | ECC |
| Voltage | 1.2 V |
| Module Height | Standard |
| Condition | New · Used |
Samsung 8 GB DDR4-2133 ECC registered RDIMM, single rank of x4 devices on a standard 288-pin registered module at 1.2 V. Rated PC4-17000 with CAS latency 15, 14.06 ns at the 1,066 MHz clock, and 17.1 GB/s peak per 64-bit channel.
Two things separate it from the 8 GB modules around it. The speed block is PB, which is 2,133 rather than 2,400, so a machine that runs at 2,400 will accept this module but drag that channel down to its own clock. And the organisation is x4, eighteen devices per rank rather than the nine that x8 would take, which is how 8 GB fits in a single rank and why the population guide's x4 table applies rather than the generic capacity line.
Every code in the table below is the same 8 GB 1Rx4 module at 2,133 MT/s. The block before the dash fixes family, device width and die revision; the dash and its tail are what a purchase order or an invoice actually names, and Samsung publishes no public decoder for them.
| Part number | M393A1G40EB1-CPB, with the nine ordering codes listed under Ordering codes (catalogue code M393A1G40EB1) |
|---|---|
| Capacity | 8 GB per module, single module |
| Organisation | 1Rx4 — one rank of x4 devices, eighteen devices for the 72-bit path, sixteen for data and two for the check bits |
| Speed | DDR4-2133, PC4-17000, 2,133 MT/s, 17.1 GB/s peak per 64-bit channel |
| Timings | CL15 at 1,066 MHz, 14.06 ns; JEDEC 2133P bin |
| Voltage | 1.2 V nominal |
| Form factor | 288-pin RDIMM, standard height 31.25 mm, bare PCB with no heatspreader |
| Register | On-module register buffers the command and address bus, so the module needs a controller that supports registered memory |
| Error handling | ECC across the 64-bit data path, plus parity on the registered command and address path |
| Manufacture | Samsung; assembly site and date code vary by production run and are printed on the module, not fixed by the part number |
| Condition | New and tested pulls, both stocked |
The label on this 2,133 MT/s module settles three things at a glance: capacity, the 1Rx4 organisation and the PC4-17000 bin, whose P letter fixes CL15. Everything else on it — revision letters, SPD level and the YYWW date — belongs to the production run, and is decoded below rather than asserted.
| Printed as | Means | Why it decides a purchase |
|---|---|---|
| 8GB | Capacity of this one module | Sets how many slots are needed for the target memory size, and it is the one number a platform setting cannot change |
| 1Rx4 | Single rank, x4 device width | One rank is the lightest load a channel can carry, but x4 devices mean twice as many of them as x8, so the rank is not as light as its name suggests |
| PC4-17000P | DDR4-2133, JEDEC bin P, which is CL15 | The bin letter is the timing grade, not a vendor code; a listing that says PC4-2133 without the letter has not specified latency |
| -R | Registered, not unbuffered | An unbuffered module of the same capacity looks similar from above and will not post in a registered-only board |
| EB1 | Die revision, the block between the density field and the speed code | Same capacity, rank and speed as the neighbouring revisions; it records which component generation the module was built from |
| CPB0 … CPBQ | Ordering tail, the characters after the speed block | The field a BOM or an invoice names. It does not change capacity, rank or speed, all of which are fixed earlier in the code |
| Raw card block | Revision and raw card design, the characters before the SPD number | Matters where a platform qualification list names a specific raw card for a slot population |
| SPD revision | Two-digit JEDEC SPD revision level | Older firmware reads lower revisions more reliably; this generation is old enough that the difference still shows up |
| YYWW | Date code, year and week | Age of the stock; on pulls it is the first evidence of how long the module has been in service |
A rank is exactly 72 bits wide — 64 for data, 8 for check — and an x4 device carries four of them, so eighteen devices make one rank. That is why 8 GB at 2,133 sits in a single rank on an x4 build: the 2Rx8 version of the same capacity uses the same eighteen devices as two ranks of nine wider parts.
The electrical cost is the flip side: eighteen x4 devices hang off one rank at 2,133 where nine x8 devices would do, roughly doubling the capacitance charged on each transfer. The register absorbs part of that on the command and address side, but guides still publish separate x4 and x8 tables — and this part is governed by the x4 one.
In practice the x4 penalty shows up when a channel is filled. One module per channel is light enough for the rated clock almost everywhere; two or three per channel is where some boards take a speed step earlier with x4 than they would with x8.
Eight gigabytes per slot at the base DDR4 speed is the workhorse of the first two DDR4 server generations. One module per channel on an eight-slot board is 64 GB, twelve slots is 96 GB, sixteen is 128 GB and twenty-four is 192 GB, and at one module per channel the rank load stays low enough that the rated 2,133 is normally held.
It is also the safe replacement unit. Where a machine was built with 8 GB modules at this speed and one fails, matching capacity, rank and revision keeps the channel uniform; fitting a 2,400 part in one slot looks like an upgrade and instead changes nothing, because the channel still runs at the slowest module present.
Count the slots before choosing a module: an 8 GB 1Rx4 population at 2,133 gives 64 GB across eight slots, 96 GB at twelve, 128 GB at sixteen and 192 GB at twenty-four. The same sixteen slots filled with 32 GB parts is 512 GB — this module is the balanced line, not the dense one.
Compatibility is settled before anything else: DDR3 will not seat in a DDR4 slot, an unbuffered module will not post in a registered-only board, and DDR5 changes the notch. What remains to choose for an 8 GB 1Rx4 part at 2,133 is capacity, rank and clock.
Speed is the variable that catches people on this part. A 2,133 module added to a channel of 2,400 parts pulls the whole channel to 2,133, and nothing announces it: the machine posts, the capacity is right, and only the firmware log or a benchmark shows the step down. Where a population has been mixed by accident, the slower module is the one to remove.
Device width matters as well. Mixing x4 with x8 modules in one channel means the channel runs on the timing derived from the heavier module, which is the x4 one, and the combination sits outside both of the guide's tables. Mixing capacities leaves the channel interleaving at the smaller size. One matched module per channel, then a second matched set, with rank, revision and width uniform inside a channel, is the pattern that behaves predictably.
No DDR4 RDIMM platform refuses 2,133, which is the bottom rung of the generation: every controller rated above it takes this 1Rx4 module and runs the channel at the module's own clock. The three pages that pair naturally with it:
None of them rejects a 1Rx4 module at 2,133; what varies is the clock the host applies to it. The speed on the code describes capability, never the machine's setting.
Samsung lists this revision end-of-life on its module page, so supply is what the secondary market holds: remaining new stock and pulls that have been tested. Both are stocked and both carry the same one year of cover, which is the practical answer for a platform that is itself several generations old.
| Code | Type | Build tail | Condition | Quote |
|---|---|---|---|---|
| M393A1G40EB1 | Catalogue code | Family code without a speed block; the P build listed here is the PC4-17000 / 2,133 MT/s one | New / used | Enquire |
| M393A1G40EB1-CPB | Ordering code | Base ordering code, no tail appended | New / used | Enquire |
| M393A1G40EB1-CPB0 | Ordering code | 0 | New / used | Enquire |
| M393A1G40EB1-CPB00 | Ordering code | 00 | New / used | Enquire |
| M393A1G40EB1-CPB0Q | Ordering code | 0Q | New / used | Enquire |
| M393A1G40EB1-CPB0QS | Ordering code | 0QS | New / used | Enquire |
| M393A1G40EB1-CPB20 | Ordering code | 20 | New / used | Enquire |
| M393A1G40EB1-CPB2Q | Ordering code | 2Q | New / used | Enquire |
| M393A1G40EB1-CPB3Q | Ordering code | 3Q | New / used | Enquire |
| M393A1G40EB1-CPBQ | Ordering code | Q | New / used | Enquire |
Cover runs one year from dispatch on both conditions, new and pulled, logged against M393A1G40EB1-CPB and the batch so a claim never rests on the invoice surviving. Pulled stock is matched and tested before packing and the sheet travels with the order; warehouse stock leaves in three to seven working days with tracking at dispatch, two pieces minimum.
The figure above is the starting price per module at the minimum quantity. Above a single tray the M393A1G40EB1-CPB line is quoted, since per-piece pricing tracks volume and condition; the same-day answer applies at any quantity once the code and platform are known.
Tell us who you are — we reply within one working day with a firm quote, stock status and lead time. Volume discounts available.
16 GB DDR4-2933 PC4-23400 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; six ordering codes under M393A2K43CB2-CVF with BY, CO, BQ, C0 and GQ tails
16 GB DDR4-2400 PC4-19200 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; eighteen ordering codes under the M393A2K43BB1 and M393A2K43CB1 revisions
16 GB DDR4-2133 PC4-17000 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; nine ordering codes from M393A2K43BB1-CPB through the CPBQ tail
16 GB DDR4-2666 PC4-21300 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; six ordering codes under M393A2K43BB1-CTD with 6Q, 6Y, 7Q, 7Y and 8Q tails