4 GB DDR4-2133 PC4-17000 ECC registered RDIMM, 1Rx8, 1.2 V, 288-pin; eight ordering codes from M393A5143DB0-CPB0 to -CPBQ
| Capacity | 4 GB |
|---|---|
| Memory Type | DDR4 |
| Speed | 2133 MT/s |
| Form Factor | RDIMM |
| Rank | 1Rx8 |
| ECC | ECC |
| Voltage | 1.2 V |
| Module Height | Standard |
| Condition | New · Used |
Samsung 4 GB DDR4-2133 ECC registered RDIMM, single rank of x8 devices on a standard 288-pin registered module at 1.2 V. Rated PC4-17000 with CAS latency 15, which is 14.06 ns at the 1,066 MHz clock — the base DDR4 speed that every registered platform of the generation accepts, and the one a module falls back to when the rest of the channel is slower than the label.
It carries the same catalogue code as the 2,400 version that sits on a separate page, but the speed block is different, so this is a different part with a different price and a different population. Buyers matching a bill of materials should check the block after the catalogue code: PB is 2,133, RC is 2,400, and mixing the two inside one channel drops the channel to 2,133.
Eight ordering codes ship against it, all built on the same catalogue code. They are listed further down so an exact code from a BOM or an invoice can be matched without hunting through eight near-identical pages.
| Part number | M393A5143DB0-CPB, with the eight ordering codes listed under Ordering codes (catalogue code M393A5143DB0) |
|---|---|
| Capacity | 4 GB per module, single module |
| Organisation | 1Rx8 — one rank of x8 devices, nine devices for the 72-bit path, eight for data and one for the check bits |
| Speed | DDR4-2133, PC4-17000, 2,133 MT/s, 17.1 GB/s peak per 64-bit channel |
| Timings | CL15 at 1,066 MHz, 14.06 ns; JEDEC 2133P bin |
| Voltage | 1.2 V nominal |
| Form factor | 288-pin RDIMM, standard height 31.25 mm, bare PCB with no heatspreader |
| Register | On-module register buffers the command and address bus, so the module needs a controller that supports registered memory |
| Error handling | ECC across the 64-bit data path, plus parity on the registered command and address path |
| Manufacture | Samsung; assembly site and date code vary by production run and are printed on the module, not fixed by the part number |
| Condition | New and tested pulls, both stocked |
Read left to right, a Samsung RDIMM label gives 4 GB first, then 1Rx8, then the PC4-17000 code whose P suffix fixes CL15. What follows belongs to the batch rather than the part number, so it is decoded below rather than stated as fact.
| Printed as | Means | Why it decides a purchase |
|---|---|---|
| 4GB | Capacity of this one module | Sets how many slots are needed for the target memory size, and it is the one number a platform setting cannot change |
| 1Rx8 | Single rank, x8 device width | One rank is the lightest load a channel can carry, which is what keeps a fully populated machine at its rated speed |
| PC4-17000P | DDR4-2133, JEDEC bin P, which is CL15 | The bin letter is the timing grade, not a vendor code; a listing that says PC4-2133 without the letter has not specified latency |
| -R | Registered, not unbuffered | An unbuffered module of the same capacity looks similar from above and will not post in a registered-only board |
| CPB0 … CPBQ | Ordering tail, the characters after the speed block | The field a BOM or an invoice names. It does not change capacity, rank or speed, all of which are fixed earlier in the code |
| Raw card block | Revision and raw card design, the characters before the SPD number | Matters where a platform qualification list names a specific raw card for a slot population |
| SPD revision | Two-digit JEDEC SPD revision level | Older firmware reads lower revisions more reliably; this generation is old enough that the difference still shows up |
| Die revision | Letter in the part number, after the density field | Mixed die revisions inside one channel are the usual cause of a machine that trains below its label speed |
| YYWW | Date code, year and week | Age of the stock; on pulls it is the first evidence of how long the module has been in service |
Four gigabytes in a single rank on the 2,133 MT/s bin is nine x8 devices of 4 Gb each — 72 bits, one rank, the lightest load a channel can be asked to carry. Nine devices is the floor for a registered module, and the 8 GB 2Rx8 part that looks similar on the shelf uses eighteen of them in two ranks to double the capacity.
That matters at two modules per channel: a 4 GB 1Rx8 population at 2,133 stays at two ranks per channel where 8 GB 2Rx8 parts would be at four, so the rated clock is easier to hold on a fully populated older board. The cost is capacity per slot, which on a machine that needs tens of gigabytes is the right trade.
This is the speed that fills the gap in older machines. A DDR4-2400 module in a platform rated at 2,133 simply trains down, but a platform whose firmware is picky about SPD timing is better served by a module that carries the 2,133 bin natively, and the price per slot is the lowest in the registered DDR4 range.
The arithmetic is the same as at any speed: eight slots is 32 GB, twelve is 48 GB, sixteen is 64 GB and twenty-four is 96 GB. For a bare-metal appliance, a build server, a storage controller pair or a lab machine kept alive for one application, that is the right size, and a single-rank x8 module is the lightest load a channel can take, so a fully populated machine keeps its rated clock instead of stepping down.
What it is not for is density. Four modules per channel of 4 GB is 16 GB per channel, where the same four slots with 32 GB parts is 128 GB. Capacity builds belong on the larger pages; this one is the small-quantity and repair line.
Generation and signal type come first — DDR3 does not fit, unbuffered does not post in a registered board, DDR5 uses another notch — and only then do the variables matter: for this 2,133 1Rx8 module they are capacity, rank and the clock the host applies.
Speed is the one that catches people on this part. A 2,133 module added to a channel of 2,400 parts pulls the whole channel to 2,133, and the drop is silent: the machine posts, the capacity is right, and only a benchmark or the firmware log shows the step down. Where the population is mixed by accident, the slower module is the one to remove, not the faster ones.
Mixing capacities in one channel leaves that channel interleaving at the smaller size, so the larger module is partly wasted. Mixing ranks inside a channel is the usual cause of a speed step, because the controller has to serve two or four banks behind one register. The safe pattern is one matched module per channel, then a second matched set, with rank and die revision uniform inside a channel.
2,133 is the floor every DDR4 registered platform accepts, so a 1Rx8 module at this speed never needs a compatibility argument — it runs at its own bin and sets the ceiling. Three pages worth reading beside it:
Compatibility is not the question with this 2,133 1Rx8 part — clock and population are. Treat the 2,133 figure as the module's ceiling and the platform guide as the authority on what it will run at.
Every code in the table below is the same 4 GB 1Rx8 module at 2,133 MT/s. The block before the dash fixes family, device width and die revision; the dash and its tail are what a purchase order or an invoice actually names, and Samsung publishes no public decoder for them.
| Code | Type | Build tail | Condition | Quote |
|---|---|---|---|---|
| M393A5143DB0 | Catalogue code | Family code without a speed block; the P build listed here is the PC4-17000 / 2,133 MT/s one | New / used | Enquire |
| M393A5143DB0-CPB | Ordering code | Base ordering code, no tail appended | New / used | Enquire |
| M393A5143DB0-CPB0 | Ordering code | 0 | New / used | Enquire |
| M393A5143DB0-CPB00 | Ordering code | 00 | New / used | Enquire |
| M393A5143DB0-CPB0Q | Ordering code | 0Q | New / used | Enquire |
| M393A5143DB0-CPB0QS | Ordering code | 0QS | New / used | Enquire |
| M393A5143DB0-CPB20 | Ordering code | 20 | New / used | Enquire |
| M393A5143DB0-CPB2Q | Ordering code | 2Q | New / used | Enquire |
| M393A5143DB0-CPBQ | Ordering code | Q | New / used | Enquire |
The M393A5143DB0-CPB line carries one year of cover from dispatch, new or pulled, recorded per part number and batch. Every pull is tested as a matched set before packing and that result ships with the module; orders leave in three to seven working days, two pieces minimum.
The figure above is the starting price per module at the minimum quantity. Above a single tray the M393A5143DB0-CPB line is quoted, since per-piece pricing tracks volume and condition; the same-day answer applies at any quantity once the code and platform are known.
Tell us who you are — we reply within one working day with a firm quote, stock status and lead time. Volume discounts available.
16 GB DDR4-2933 PC4-23400 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; six ordering codes under M393A2K43CB2-CVF with BY, CO, BQ, C0 and GQ tails
16 GB DDR4-2400 PC4-19200 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; eighteen ordering codes under the M393A2K43BB1 and M393A2K43CB1 revisions
16 GB DDR4-2133 PC4-17000 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; nine ordering codes from M393A2K43BB1-CPB through the CPBQ tail
16 GB DDR4-2666 PC4-21300 ECC registered RDIMM, 2Rx8 on eighteen 8 Gb x8 packages, 1.2 V, 288-pin; six ordering codes under M393A2K43BB1-CTD with 6Q, 6Y, 7Q, 7Y and 8Q tails